Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Wheels

$0.25 - $18.79
Developed for short spokes with a large deflection angle. DT Pro Head nipples are designed for short spokes with a large angle of deflection, such as for e-bike use. Through the spherical contact surface, the nipple aligns automatically with the angle of the spoke, which leads to consistent power transmission. Note: brass nipples are not approved for children's products in the USA. See attached warning! All-brass nipples are recommended for e-bike use. - Weight: starting at 59g for 64 nipples.
$1.99 - $88.79
This is one of the most versatile spokes in the DT Swiss spoke range. DT competition gets its special strength from cold forging. This makes an extremely durable spoke and thanks to the thinner middle section, it is 48 g lighter (per 64 spokes) than a spoke with a constant diameter of 1.8 mm. It is perfect for a wide range of uses, from road wheels to super light enduro MTB wheels. - Double Butted: 2.0/1.8/2.0 - One 264mm spoke = 6g - Nipples sold separately
$1.99
- Shell: 8mm flanged axle nut - Flanged
$2.99 - $88.19
Champion 2.0 Black Spokes - One 264mm spoke = 7g
$2.99 - $440.95
DT Champion 2.0 spokes cover the whole spectrum from reliable road wheels to MTB gravity wheels. - Straight pull spoke blanks - Nipples sold separately
$2.99
- For square taper and flanged. - Fits most cartridge BBs - Shell: 8mm Flanged axle bolt
$5.50
Getting the correctly sized magnets means you're worrying about where the next coffee stop is, not if your computer is recording the ride. Key features: - Universal wheel magnets work with any speed sensor - Thread-on speed magnet is positioned closer to the sensor for improved signal - Aero speed magnet provides a sleek, low-profile, aerodynamic solution
$9.00
Replacement springs and pawls. Includes 6 pawls, 6 springs and 1 plastic retaining ring that holds the pawls in place even during disassembly to ensure you're never searching the floor for tiny springs.
$9.79 - $9.99
- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity
$9.99 - $15.99
These rim valves are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Key features: - To be used exclusively with Bontrager Tubeless Ready (TLR) wheels - Required for Bontrager's Tubeless Ready (TLR) system setup - Removable valve core for easy sealant fill - Silver MTB valve is compatible with all Bontrager Mountain wheels except: Line XXX, Kovee XXX, and Line Pro 40 - Alloy Road Tubeless Rim Valve is compatible with all Bontrager alloy TLR road wheels
$9.99 - $10.30
Grade 10 chromium steel balls
$9.99
• Replacement aluminum quick release skewers
$9.99
• Replacement aluminum quick release skewers
$9.99
• Replacement aluminum quick release skewers
$9.99
High-quality replacement skewer to keep the bike moving. - OE Replacement skewers - Available in a variety of OE replacement lengths - Measure hub width and skewer length to ensure proper compatibility
$11.99
Dynaplug tubeless tire repair plugs are constructed from viscoelastic rubber impregnated cord and non-abrasive brass tip. The plugs are specially designed to be inserted directly into a puncture after object has been removed. - Pack of 5 replacement plugs with pointed brass soft nose tip - Compatible with all Dynaplug repair tools, except for Air Road tool - Made in USA
$12.50 - $29.99
- Anodized aluminum - 50 nipples per bag - 12mm length
$12.99 - $15.99
Tubeless setup made easy with valve stems designed to work as a system with Bontrager wheels, tires and rim strips The valves you need to upgrade to Tubeless These rim valves are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Product details - To be used exclusively with Bontrager Tubeless Ready (TLR) wheels - Use only with Bontrager TLR rim strip with rectangular base - Required for Bontrager's Tubeless Ready (TLR) system setup - Removable valve core for easy sealant fill - Sold as singles
$14.99 - $15.99
- To be used exclusively with Bontrager 29""/700c Tubeless Ready (TLR) wheels - TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion - Rim Strip replacement is recommended if removed from the wheel
$15.50 - $24.99
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
$17.00
Pro Head Reinforcement System (PHR) has a larger and more spherical contact area and is designed to balance loads transferred to the rim. The PHR system acts as a ball and socket interface, allowing the spoke to pivot into alignment while maintaining even, consistent contact during installation in order to follow the perfect trajectory from the hub to the rim.
$19.99
- To be used exclusively with Bontrager 29""/700c Tubeless Ready (TLR) wheels - TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion - Rim Strip replacement is recommended if removed from the wheel
$20.99
To be used exclusively with Bontrager Tubeless Ready (TLR) rims. The rim strips you need to upgrade to Tubeless These rim strips are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Product details - TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion - Use only with appropriate Bontrager TLR rim valve - Rim strip replacement is recommended if removed from the wheel - Sold as singles - White strip is recommended for carbon rims - TLR rim valve sold separately
$20.99
These rim strips are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Key features: - To be used exclusively with Bontrager 29"/700c Tubeless Ready (TLR) wheels - TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion - Rim Strip replacement is recommended if removed from the wheel - For specific compatibility, access 'WHEELS' tab on the Tech Site or contact Customer Service
$21.80 - $51.59
Ease of use, lightweight, and optimum performance in a single product. The DT Pro Head shape, combined with both a torx and a square tool interface, makes wheel building a lot easier. The spherical contact surface aligns the nipple perfectly with the spoke. All-brass nipples are recommended for e-bike use. Weight: starting at 26g for 64 nipples.
$23.99 - $29.99
Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.
$26.99
Bontrager's new Elite Skewers better integrate into your frame for better aerodynamics and aesthetics, while the premium internal cam design ensures these are here to last Key features: - New Elite Skewer integrates better into the frame for optimized aerodynamics - Internal cam design looks great, lasts longer, and offers quick, easy operation
$33.99
Upgrade or refresh your bike. When it's time to refresh your trusty bike, Trek Genuine Replacement Parts have you covered. PRODUCT DETAILS - Original equipment replacement kids wheels - Does not include skewer, reflector, rim strip, valve, or owner's manual - Wheels shipped as photographed
$36.99
Upgrade or refresh your Bontrager wheels. - Replacement axle for Bontrager hub - Compatible with Aeolus Pro Disc, Paradigm Comp Disc and Paradigm TLR Disc
$38.00
- Cold forged 2.0mm 304 stainless steel with rolled threads - Nipples sold separately - 213g (32 spokes @ 262mm) - Bag of 50
Page 1 of 2 Next page